2.4G Connection：

Make sure the Controller operating status slide switch is in the 2.4G position. Insert the included 2.4G Receiver into a PC, Android device, Switch console dock, or PlayStation 3 console, then press the controller power button to turn on the Controller. The purple indicator for the corresponding mode lights.

* When using 2.4G for the first time, pairing with the Receiver is required. Press and hold the Bluetooth Pairing button until the purple indicator flashes quickly.

USB Connection：

Make sure the Controller operating status slide switch is in the OFF position. Connect the included USB to Type-C data cable. After the Controller automatically detects the mode required by the connected device, the corresponding orange indicator lights.indicator lights.
Automatically recognized device types: Windows PC / Android device / Nintendo Switch / Nintendo Switch 2 / Sony PlayStation 3
If automatic device recognition is incorrect, or if certain software requires a specific wired mode, you can force the Controller to connect in a specified wired mode.
With the Controller slide switch in the OFF position and no cable connected, hold one of the A/B/X/Y buttons while connecting the USB to Type-C data cable to start the selected wired mode.

• [X] button: Xbox 360 Controller wired mode (Xinput wired protocol)
• [A] button: General Controller wired mode (Dinput wired protocol)
• [Y] button: Pro Controller wired mode (wired Controller connection must be enabled in Switch console settings)
• [B] button: PlayStation 3 Controller wired mode

Bluetooth Connection：

Make sure the controller operating status slide switch is in the Bluetooth position, then press the controller power button.
Turn on the Controller. A slow-flashing blue indicator means Bluetooth reconnection is in progress. At this time, press and hold the [MODE] button on the Controller to cycle through connection modes. After selecting the required connection mode, press and holdthe Bluetooth Pairing button to start Bluetooth pairing mode. Release the button when the blue indicator flashes quickly, then select the Bluetooth broadcast name for the chosen mode on the device you want to connect.

Bluetooth Mode：

• X mode: Connects by Bluetooth to computers, Android devices, iOS devices, and other devices as an Xbox-style Controller.
• D mode: Connects by Bluetooth to various devices as a general Controller (Dinput protocol).
• S mode: Connects by Bluetooth to Switch/Switch Lite/Switch 2 asPro Controller.
• T mode: Connects by Bluetooth to Android devices in touchscreen mapping mode (virtual touch mode).
  
  

Button Layout

Charging & Remaining Battery Check

The rechargeable battery installed in the Controller is not fully charged at first.

• Charge it before use：
  Connect thecontroller toa computer game console, USB chargeror power bank usinga USB to Type-C charging & data cable.
• During Charging：
  While charging, the indicators flash from empty to full.
  ( Red indicator lights turn on ;the last battery level indicator flashes.)
• Charging Complete:
  When charging is finished, all four red indicator lights stay steadily lit.
• Remaining Battery Check：
  During Controller use, press [Fn] and [MODE] to display the remaining battery power. The built-in battery level is shown for about 3 seconds in the following four states. Indicator LED Indicator LED Status.
  *When the target battery level is below 10%, the current mode indicator for Bluetooth 1/Bluetooth 2/2.4G flashes as a warning.

Linear Trigger & Quick Trigger Switching

Linear Trigger function ON (long travel)：Slide the lock switch next to the LT/RT triggers toward the Type-C port. The triggers provide approximately 4 mm of travel for precise analog control.

Linear Trigger function OFF (short travel)：Slide the lock switch back toward you. The triggers provide approximately 2 mm of short travel for faster actuation.

*Linear Trigger functionality may not be available in every connection mode or game. Do not force the LT/RT buttons while switching trigger modes.

Pair with a Switch/Switch 2

Pairing with the Switch ：Pairing is required the first time the Controller connects to a Switch console.
Connect the included Type-C data cable to the Switch dock. The Controller automatically recognizes the connected device and uses Pro Controller wired mode. At the same time, Bluetooth Pairing information for the Controller and Switch console is saved automatically. After the wired connection is disconnected, the Controller can switch to Bluetooth wireless mode and automatically connect to the Switch.

Pairing with Switch 2：This Controller supports a special method for copying Switch 2 Joy-Con wake information to enable the Switch 2 console wake function. Pairing is required the first time it connects to a Switch 2.

1. Open the Switch 2 Controller search screen.
2. Power on the Controller in Bluetooth mode on the D1 channel, then switch to S mode. Press and hold the Bluetooth Pairing button until the dark blue indicator flashes quickly to begin Pairing.
3. After the Controller shows that connection is complete, remove the second-generation JoyCon from the console within 20 seconds. Wake information will be copied automatically, and you can then try waking the Switch 2 console. If wake fails, go to "Settings" - "Controllers & Accessories" - "Disconnect Controllers" on the Switch 2 console to disconnect all connected Controllers, then repeat the steps above.

* Note: Switch 2 wake setup is supported only on Bluetooth channel D1.

Basic Operation

TURBO Settings (Rapid Fire / Auto Rapid Fire)：

• Rapid fire: Press Fn + a function button to start.
• Auto rapid fire: Press Fn + the same function button twice to start.
• Rapid-fire speed: Press Fn + right joystick up/down to adjust the global rapid-fire speed.
• Three levels are available: slow, medium, and fast. To cancel rapid fire, double-press Fn to cancel rapid fire for all buttons.

Recording Macros with the ML/MR Expansion Buttons：

• Recording： Press Fn + ML/MR to start macro recording. The indicator for the current mode turns red, indicating that macro recording is ready.
• Saving a macro：After entering the button sequence, press ML/MR again to save it. The red indicator turns off.
• Clearing a macro: Hold Fn and press ML/MR twice to clear it. (This saves an empty macro.)

*Macro recording supports recording up to 42 button-sequence entries, including joystick and button timing.

Mapping Buttons with the ML/MR Expansion Buttons：

When only one button is recorded to an expansion button, the expansion button functions as a mapped button.

*To change mapping for the Controller body function buttons, use the mapping menu page in the app.

Using the ML/MR Expansion Buttons for Forced Motion Control (Replacing the Right Joystick)：
When only the [■] button is recorded to an expansion button, that expansion button becomes the Motion Control activation button (the gyroscope replaces the right joystick).

• If one [■] button is recorded, hold the expansion button to enable Motion Control; release it to disable the function.
• If two [■] buttons are recorded, press the expansion button once to enable Motion Control, then press it again to disable Motion Control.

*In Switch mode, the [Screenshot] button is mapped as the screenshot/video capture button and does not function as a Motion Control switch. When 2 or more buttons other than this button are recorded, they are saved as a button sequence (macro setting).

Exchanging Control Authority When Using Two Controllers (Role Control Exchange)：

Conditions for role control exchange between two Controllers：Use 2.4G mode with two Controllers connected to one 2.4G Receiver at the same time.

Conditions for role control exchange between two Controllers:
1. Insert the 2.4G Receiver into the game console(PC/Android device /Switch/PlayStation 3)
2. Set the first Controller slide switch to the 2.4G position and turn it on. If Pairing is required, press and
hold the Bluetooth Pairing button to pair. Connect the second Controller in the same way.
*Do not use the Receiver for another Controller of the same model during Pairing with the Receiver.
3. During a game, press Fn + [■] to exchange operating authority between the two Controllers.

Switch/PlayStation 3 Connection Channel Number Indicator：

After the Controller is connected to a Switch/PS3 console, a channel number is assigned automatically according to the device connection order, and the mode indicator changes to the corresponding color channel-number indicator.

Install the "KeyLinker" smartphone/tablet app.

The button configuration center in this app can modify more than ten functional
parameters, including Controller button mapping, Vibration intensity, joystick sensitivity, and Trigger travel. You can also set lighting colors and transition methods, adjust recorded macro parameters, and more. The Controller can remain connected to both the gaming device and the app during configuration.